1.想把五星之光HX的迷彩J20移植到南征北战，用了新建单位方法，把W3D、DDS贴图都放文件夹调整INI了。
2.造出来之后发现没有贴图（在机场建造，降落航母上方便演示）
3.UE打开W3D复核DDS文件只提及J20C.dds，没涉及tga。
4.W3D打开情况
求助各位大佬这种情况怎么处理

没贴图是粉色，你这八成是动UV了

你用3DSMAX或者RenX看一下UV，贴图不是直接用就能完美适合的，要展UV来确定某个面会用到贴图的哪个部分

用W3D查看模型的时候，模型和贴图文件需要放在同一个文件夹才行

各位大佬再看看，换了个模型，只有发射主武器抵消隐形、偶尔失去隐形时贴图正常。

光看图不确定这个黑色的J20是不是受损模型，如果是的话大概是Model =后面填错了
以这个隐形战机为例Object AmericaJetStealthFighter
SelectPortrait = SNAdvReactor_La
ButtonImage = SNAdvReactor_La
UpgradeCameo1 = Upgrade_AmericaLaserMissiles
UpgradeCameo2 = Upgrade_AmericaAdvancedTraining
UpgradeCameo3 = Upgrade_AmericaAircraftExtraFuel
UpgradeCameo4 = Upgrade_AmericaCountermeasures
UpgradeCameo5 = Upgrade_AmericaBunkerBusters
Draw = W3DModelDraw ModuleTag_01
——————正常Model = AVStealth
DefaultConditionState
Model = AVStealth
HideSubObject = BurnerFX03 BurnerFX04
WeaponLaunchBone = PRIMARY WeaponA
End
ConditionState = JETEXHAUST
ParticleSysBone = Wingtip01 JetContrail
ParticleSysBone = Wingtip02 JetContrail
End
ConditionState = JETEXHAUST JETAFTERBURNER
ParticleSysBone = Wingtip01 JetContrail
ParticleSysBone = Wingtip02 JetContrail
ShowSubObject = BurnerFX03 BurnerFX04
ParticleSysBone = Engine01 JetLenzflare
ParticleSysBone = Engine02 JetLenzflare
End
——————受损Model = AVStealth_D
ConditionState = REALLYDAMAGED
Model = AVStealth_D
ParticleSysBone = Smoke01 JetSmoke
ParticleSysBone = Engine01 JetEngineDamagedSmoke
End
ConditionState = REALLYDAMAGED JETEXHAUST
Model = AVStealth_D
ParticleSysBone = Smoke01 JetSmoke
ParticleSysBone = Engine01 JetEngineDamagedSmoke
ParticleSysBone = Wingtip01 JetContrail
ParticleSysBone = Wingtip02 JetContrail
End
ConditionState = REALLYDAMAGED JETEXHAUST JETAFTERBURNER
Model = AVStealth_D
ParticleSysBone = Smoke01 JetSmoke
ParticleSysBone = Engine01 JetEngineDamagedSmoke
ParticleSysBone = Wingtip01 JetContrail
ParticleSysBone = Wingtip02 JetContrail
ShowSubObject = BurnerFX03 BurnerFX04
ParticleSysBone = Engine01 JetLenzflare
ParticleSysBone = Engine02 JetLenzflare
End
——————被毁 Model = AVStealth_D1
ConditionState = RUBBLE
Model = AVStealth_D1
HideSubObject = None
ShowSubObject = None
End
ConditionState = RUBBLE JETEXHAUST JETAFTERBURNER
Model = AVStealth_D1
HideSubObject = None
ShowSubObject = None
ParticleSysBone = Engine01 JetExhaust
ParticleSysBone = Engine02 JetExhaust
ParticleSysBone = Wingtip01 JetContrail
ParticleSysBone = Wingtip02 JetContrail
End
OkToChangeModelColor = Yes
End
不是的话我也不知道，因为我也是自学newbie