level 8
下面教程
2016年05月29日 01点05分
level 8
level 8
level 8
level 8
level 8
level 8
qyh888qyh
楼主
首先是传感器制造商的教程
能看懂的自己看，看不懂的下面我会解释。
Kionix KXTJ9-KXCJ9-KXTJ2 Accelerometer Driver V1.28.3
Known Issue(s):
===============
There’s a problem where the screen orientation is wrong momentarily after coming out of S3 or S4.
Troubleshooting:
================
If the screen does not rotate properly, you may need to adjust the chip mount configuration. This can be done with the factory_cal tool or by editing the registry.
OPTION 1:
To use factory_cal, lay the device flat with the screen facing up and run “factory_cal –mount 2” for MAP2, replace with needed map.
OPTION 2:
The “ChipMount” value in the registry is found in device key HLKM\SYSTEM\CurrentControlSet\Enum\ROOT\SENSOR\0000\kxfusion
If device does not have chip mount info (an ACPI _CDM method), please calibrate with factory_cal or set a ChipMount value in the registry.
If the screen is rotated by 90 degrees and it changes the right way when the device is turned (screen goes counterclockwise when device goes clockwise), use DEVICE_MAP2 if the screen is counterclockwise, or DEVICE_MAP4 is it’s clockwise.
If the screen changes the wrong way (rotates the same way as the device), use DEVICE_MAP6 for counter, DEVICE_MAP8 for clockwise.
2016年05月29日 02点05分
12
能看懂的自己看，看不懂的下面我会解释。
Kionix KXTJ9-KXCJ9-KXTJ2 Accelerometer Driver V1.28.3
Known Issue(s):
===============
There’s a problem where the screen orientation is wrong momentarily after coming out of S3 or S4.
Troubleshooting:
================
If the screen does not rotate properly, you may need to adjust the chip mount configuration. This can be done with the factory_cal tool or by editing the registry.
OPTION 1:
To use factory_cal, lay the device flat with the screen facing up and run “factory_cal –mount 2” for MAP2, replace with needed map.
OPTION 2:
The “ChipMount” value in the registry is found in device key HLKM\SYSTEM\CurrentControlSet\Enum\ROOT\SENSOR\0000\kxfusion
If device does not have chip mount info (an ACPI _CDM method), please calibrate with factory_cal or set a ChipMount value in the registry.
If the screen is rotated by 90 degrees and it changes the right way when the device is turned (screen goes counterclockwise when device goes clockwise), use DEVICE_MAP2 if the screen is counterclockwise, or DEVICE_MAP4 is it’s clockwise.
If the screen changes the wrong way (rotates the same way as the device), use DEVICE_MAP6 for counter, DEVICE_MAP8 for clockwise.
level 8
qyh888qyh
楼主
百度翻译版（很糟糕）
kionix kxtj9二kxcj9 kxtj2 v1。.二十八宿.三accelerometer司机
知者（S）：
万万万万万万万万万万万万万万万
有问者，误也momentarily where the screen of S3或S4出。
troubleshooting：
万万万万万万万万万万万万万万万万
rotate does其if the屏properly You need to the，梅宏芯片装置。This can be done with the CAL式编具或所_ the注。
选项。：
用所_ to the device卡尔，在夷之屏上与run with the“厂_卡尔–mount二“replace with needed for MAP2，图。
选项！：
“chipmount is found in the注直在要置\统\ hlkm currentcontrolset \ \ \ \ 0000 ENUM之kxfusion根传感器
若device does其have芯片（ACPI之CDM信安山_ method），请与厂校准校准直或_ chipmount茶集注。
if the屏旋90度与EN is by changes when the device is the right也（转身去counterclockwise屏置上用时，clockwise）_ MAP2 if the device is counterclockwise屏，或clockwise _ map4 device is。
if the changes the wrong屏路（the same as the device路rotates device），用_ map6 for device for clockwise _ map8计数器。
2016年05月29日 02点05分
13
kionix kxtj9二kxcj9 kxtj2 v1。.二十八宿.三accelerometer司机
知者（S）：
万万万万万万万万万万万万万万万
有问者，误也momentarily where the screen of S3或S4出。
troubleshooting：
万万万万万万万万万万万万万万万万
rotate does其if the屏properly You need to the，梅宏芯片装置。This can be done with the CAL式编具或所_ the注。
选项。：
用所_ to the device卡尔，在夷之屏上与run with the“厂_卡尔–mount二“replace with needed for MAP2，图。
选项！：
“chipmount is found in the注直在要置\统\ hlkm currentcontrolset \ \ \ \ 0000 ENUM之kxfusion根传感器
若device does其have芯片（ACPI之CDM信安山_ method），请与厂校准校准直或_ chipmount茶集注。
if the屏旋90度与EN is by changes when the device is the right也（转身去counterclockwise屏置上用时，clockwise）_ MAP2 if the device is counterclockwise屏，或clockwise _ map4 device is。
if the changes the wrong屏路（the same as the device路rotates device），用_ map6 for device for clockwise _ map8计数器。