level 5
苏州电脑中心
楼主
原帖 ：http://bbs.gfan.com/android-4966728-1-1.html
在G22刷机s-off的时候，用导线短接折腾了几个小时，看了官方说明才终于成功了。
注意：短接的时候要连续两次短接。
"Do wire-trick now!! check..."出现时，立即短接一下，同时密切注视电脑资源管理中的可移动存储设备，当手机的存储设备消失瞬间同时命令行窗口没有出现新的提示时，再短接一下。
"let's take one more..."出现时，同样需要短接两下。
记住：当出现提示时，需要短接两下而不是一下，中间约1.5秒（差不多就行）。
附件：G22短接位置示意图片，软件传不上，请参考其他教程帖。
下面附s-off软件官方地址和说明英文（括号中为我简短翻译的）：http://unlimited.io/jb_ruby.htm
s-off前准备工作：
In order to use JuopunutBear you must meet the following pre-requisites:
1.Be unlocked using the HTCdev bootloader unlock.（htc解锁，参考其他教程帖）
2.Be on the stock ROM and be rooted (have superuser and/or an unsecured boot image installed).（recovery和root，参考其他教程帖）
3.Some custom ROMs may work, however we cannot verify them all. If you are not using a stock ROM and have problems then this is most likely the reason.
4.Have a spare microSD card or to have backed up all contents of your SDcard, the card may be wiped, while we try to restore the card to it's original state it is possible that this will not succeed.（可用的SD卡，不要保存重要数据，s-off中会擦写SD卡）
5.Have fastboot and adb drivers installed and working (windows).（参考其他教程帖，android文件夹里有）
6.Have usb debugging enabled.（usb开发模式打开）
7.Uninstall any potentially interfering phone software which such as HTC sync, Andro sync, PDAnet etc, iTunes has also been noted to cause issues.（卸载其他可能干扰的软件htc sync, andro sync, pdanet等，s-off时彻底关掉这些就行，iTunes会干扰，最好删掉）
8.Have a piece of insulated wire of sufficient length to join the contact points for your device. See images and videos for device specific information.（准备一根长度合适的导线）
s-off导线短接注意事项：
When instructed to do so by the program you must perform the "wire trick" as follows:
1.Obtain an insulated wire of appropriate length and gauge. Suitable wires are: a core from an ethernet cable, the center core from a coaxial cable, a paperclip wrapped in non-conductive tape (electrical tape, masking tape, or scotch tape will work).（准备好导线，最好单股硬点的，貌似网线不错）
2.Insert one end of the wire into the hole where PIN is indicated in the picture below, ensuring that a firm contact is made with the metal contact at the bottom of the hole.（导线一端插入图示小孔，确保和下面的金属点接触）
3.Briefly touch to other end of the wire to the contact marked GND in the picture below.（导线另一端在短接时短暂的触碰sd卡金属外壳）
4.Wait approximately 1.5 seconds and then again touch the wire to the marked GND. （等待约1.5秒后，再短接一次）
5.Allow the program to continue.（程序继续运行）
Note: On one device used during testing we discovered that an internal label (the circle that can be seen through the back cover above PIN in the photo below) was misplaced and was covering the contact point. If that is the case on your device this can be remedied by powering off you phone and removing the battery, then using a sharp pin or needle to scrape away the parts of the label covering the contact point.
Note: It may take several attempts of running the program in order to obtain the correct timing for the wire trick.
G22 s-off 导线短接位置.jpg (61.14 KB)
G22 s-off 导线短接位置.jpg (61.14 KB)
2013年01月09日 16点01分
1
在G22刷机s-off的时候，用导线短接折腾了几个小时，看了官方说明才终于成功了。
注意：短接的时候要连续两次短接。
"Do wire-trick now!! check..."出现时，立即短接一下，同时密切注视电脑资源管理中的可移动存储设备，当手机的存储设备消失瞬间同时命令行窗口没有出现新的提示时，再短接一下。
"let's take one more..."出现时，同样需要短接两下。
记住：当出现提示时，需要短接两下而不是一下，中间约1.5秒（差不多就行）。
附件：G22短接位置示意图片，软件传不上，请参考其他教程帖。
下面附s-off软件官方地址和说明英文（括号中为我简短翻译的）：http://unlimited.io/jb_ruby.htm
s-off前准备工作：
In order to use JuopunutBear you must meet the following pre-requisites:
1.Be unlocked using the HTCdev bootloader unlock.（htc解锁，参考其他教程帖）
2.Be on the stock ROM and be rooted (have superuser and/or an unsecured boot image installed).（recovery和root，参考其他教程帖）
3.Some custom ROMs may work, however we cannot verify them all. If you are not using a stock ROM and have problems then this is most likely the reason.
4.Have a spare microSD card or to have backed up all contents of your SDcard, the card may be wiped, while we try to restore the card to it's original state it is possible that this will not succeed.（可用的SD卡，不要保存重要数据，s-off中会擦写SD卡）
5.Have fastboot and adb drivers installed and working (windows).（参考其他教程帖，android文件夹里有）
6.Have usb debugging enabled.（usb开发模式打开）
7.Uninstall any potentially interfering phone software which such as HTC sync, Andro sync, PDAnet etc, iTunes has also been noted to cause issues.（卸载其他可能干扰的软件htc sync, andro sync, pdanet等，s-off时彻底关掉这些就行，iTunes会干扰，最好删掉）
8.Have a piece of insulated wire of sufficient length to join the contact points for your device. See images and videos for device specific information.（准备一根长度合适的导线）
s-off导线短接注意事项：
When instructed to do so by the program you must perform the "wire trick" as follows:
1.Obtain an insulated wire of appropriate length and gauge. Suitable wires are: a core from an ethernet cable, the center core from a coaxial cable, a paperclip wrapped in non-conductive tape (electrical tape, masking tape, or scotch tape will work).（准备好导线，最好单股硬点的，貌似网线不错）
2.Insert one end of the wire into the hole where PIN is indicated in the picture below, ensuring that a firm contact is made with the metal contact at the bottom of the hole.（导线一端插入图示小孔，确保和下面的金属点接触）
3.Briefly touch to other end of the wire to the contact marked GND in the picture below.（导线另一端在短接时短暂的触碰sd卡金属外壳）
4.Wait approximately 1.5 seconds and then again touch the wire to the marked GND. （等待约1.5秒后，再短接一次）
5.Allow the program to continue.（程序继续运行）
Note: On one device used during testing we discovered that an internal label (the circle that can be seen through the back cover above PIN in the photo below) was misplaced and was covering the contact point. If that is the case on your device this can be remedied by powering off you phone and removing the battery, then using a sharp pin or needle to scrape away the parts of the label covering the contact point.
Note: It may take several attempts of running the program in order to obtain the correct timing for the wire trick.
G22 s-off 导线短接位置.jpg (61.14 KB)
G22 s-off 导线短接位置.jpg (61.14 KB)
![[背扭]](/static/emoticons/u80ccu626d.png)
