◆在路上◆ peng190210
没有等出来的美丽，只有走出来的辉煌。
关注数: 68 粉丝数: 39 发帖数: 936 关注贴吧数: 35
程序运行中机床报警，复位解除报警，程序如何从断开的那里开始？ 程序运行中机床报警，复位解除报警后，程序如何从刚断开的那里开始？ 还是必须得从头开始？ T5 M6 G0 G90 G54 X124.262 Y-51.471 A0. S2000 M3 G43 H5 Z100. M8 Z1. G1 Z-2. F100. G41 D5 X128.548 Y-47.184 F300. G3 X124.262 Y-42.898 R4.286 Y-60.044 R8.573 Y-42.898 R8.573 X119.975 Y-47.184 R4.286 G1 G40 X124.262 Y-51.471 Z-4. F100. G41 D5 X128.548 Y-47.184 F300. G3 X124.262 Y-42.898 R4.286 Y-60.044 R8.573 Y-42.898 R8.573 X119.975 Y-47.184 R4.286 G1 G40 X124.262 Y-51.471 Z-6. F100. G41 D5 X128.548 Y-47.184 F300. G3 X124.262 Y-42.898 R4.286 Y-60.044 R8.573 Y-42.898 R8.573 X119.975 Y-47.184 R4.286 G1 G40 X124.262 Y-51.471 Z-8. F100. G41 D5 X128.548 Y-47.184 F300. G3 X124.262 Y-42.898 R4.286 Y-60.044 R8.573 Y-42.898 R8.573 X119.975 Y-47.184 R4.286 G1 G40 X124.262 Y-51.471 Z-10. F100. G41 D5 X128.548 Y-47.184 F300. G3 X124.262 Y-42.898 R4.286 Y-60.044 R8.573 Y-42.898 R8.573 X119.975 Y-47.184 R4.286 G1 G40 X124.262 Y-51.471 Z-12. F100. G41 D5 X128.548 Y-47.184 F300. G3 X124.262 Y-42.898 R4.286 Y-60.044 R8.573 Y-42.898 R8.573 X119.975 Y-47.184 R4.286 G1 G40 X124.262 Y-51.471 Z-14. F100. G41 D5 X128.548 Y-47.184 F300. G3 X124.262 Y-42.898 R4.286 Y-60.044 R8.573 Y-42.898 R8.573 X119.975 Y-47.184 R4.286 G1 G40 X124.262 Y-51.471 Z-16. F100. G41 D5 X128.548 Y-47.184 F300. G3 X124.262 Y-42.898 R4.286 Y-60.044 R8.573 Y-42.898 R8.573 X119.975 Y-47.184 R4.286 G1 G40 X124.262 Y-51.471 Z-18. F100. G41 D5 X128.548 Y-47.184 F300. G3 X124.262 Y-42.898 R4.286 Y-60.044 R8.573 Y-42.898 R8.573
求大神指点，加工中心换刀时撞刀怎么解决？ 在换刀程序执行的一半时，机床气压不足出现报警，然后我就手动按了机床侧面液压表那地方的一个按钮，刀库退回去了，然后就按急停。结果再执行换刀程序时，主轴降到和刀库等高的位置，然后刀库横着过来就撞到主轴上了，这是什么情况？请大神指点一下。
1 下一页